a ramp that is too short: with a track car, the problem often comes down to a few millimetres. Using ramps for low cars therefore means far more than simply placing them on the ground. You need a gradual, stable climb, perfectly aligned with the wheels, so that the aerodynamics, bodywork and mechanical components stay protected.
On a prepared GT, a race car, a lowered classic or a car fitted with a body kit, reduced ground clearance is part of the car’s identity. It should not become a constraint every time you load. Well-chosen and correctly installed loading ramps turn this operation into a precise, quick and reassuring step in the paddock.
Ramps for low cars: understanding the approach angle
The first criterion is not the final height of the ramp but its slope. A tall, short ramp creates an angle that is too steep: the front wheels climb while the front lip, front diffuser or floor stays too close to the ground. A long ramp, on the other hand, spreads the height difference and reduces the risk of contact.
Your car’s approach angle depends on several factors: front overhang, the actual height of the front lip, tyre diameter, suspension and any aerodynamic appendages. A slightly lowered road car will accept a slope that a track car with an aggressive front splitter will refuse. Never rely solely on a “ramp for low cars” label.
The transition at the top deserves the same attention. Even with a gentle slope, an abrupt break between the ramp and the trailer bed can make the underside of the body touch as the rear wheels begin to climb. Ramps with a progressive profile, or ramp extensions, limit this rocking effect. For the lowest cars, two stages of incline may be preferable to a single, very steep ramp.
Measure before choosing your loading ramps
Before any purchase or first use, measure the ground clearance at the lowest point at the front. Do it with the car in its usual transport configuration: tyre pressures, ride height, splitter fitted and, if necessary, a fuel level close to reality. A variation of a few millimetres can change how a slope is negotiated.
Also note the distance between the tip of the front lip and the centre of the front wheel. This figure gives a more accurate idea of the angle the car can accept. If you use a trailer or a truck, measure the height difference between the ground and the bed, as well as the space available to deploy the ramps without creating a sideways slope.
The usable width must suit your track width and tyres. A ramp that is too narrow makes guiding difficult, especially with wide semi-slick tires or in the wet. A ramp that is too light, or not rated for the axle load, is no saving: it can bend, slip or deform. Always check the load rating stated for the pair, not just for a single ramp.
Prepare stable ground and a clean trailer bed
A good installation starts at ground level. Place the ramps on a firm, level surface, free of gravel, mud, oil or wet grass. A ramp that sits unevenly can tip as the wheel passes over it, however well it is built.
The trailer bed must be checked too. Damp patches, fuel traces and smooth metal surfaces reduce grip. Clean the contact area, then check that every hook, lip or retaining system is engaged as the manufacturer intends. A ramp simply leaned against the bed can slide back as the car gathers momentum.
Where the setup allows, secure the ramps with their dedicated anchoring system. If there is none, do not improvise with a strap placed at random: the restraint must prevent backward movement without pulling the ramp sideways. The aim is to keep two strictly parallel tracks throughout the climb.
Alignment matters more than speed
Find the centre of each front wheel before you start. On a low car, a sudden steering correction during the climb can push a tyre off the usable profile of the ramp or make a sidewall touch its edge. A second person, standing in the driver’s line of sight and never in front of the car, provides real safety.
Drive up slowly, without sharp acceleration or sudden braking. Momentum does not fix a slope that is too steep: it only increases the risk of the ramps moving and of an impact at the top. If the front lip gets dangerously close, stop. Change the angle, add an extension or choose a longer solution rather than forcing the climb.
Once the wheels are on the bed, immobilise the car before doing anything else. Handbrake, gear engaged where suitable for the transmission, then wheel chocks: each step matters before fitting the tie-down straps. Ramps never replace a proper securing procedure.
Mistakes that damage a low car
The first mistake is using ramps designed for domestic use to load a competition car. Their slope, width, material or load rating may be unsuitable. A fine car should not be compromised on the very piece of equipment that governs every entry into the truck or onto the trailer.
The second is overlooking the difference between lifting a car and loading it. Lifting ramps provide a working height, but they are not necessarily designed to reach a trailer bed. Conversely, a loading ramp should not be used as a maintenance support without clear approval from its manufacturer. To work under the car, use suitable lifting equipment and axle stands on a stable surface.
Finally, avoid improvised stacks of planks, wedges or plates. They may seem practical in an emergency, but their stability is rarely guaranteed and their transition is often abrupt. For a car with low ground clearance, equipment designed for the job remains the most elegant and most rational solution.
Adapt the solution to your paddock
The right choice depends on your environment. For an open trailer used occasionally, long, light ramps that are easy to position may be enough, provided they suit the car’s weight and ground clearance. For a team that regularly loads several cars, the priority shifts to repeatability: generous width, quick fixing, secure storage and resistance to intensive use.
Very low cars, prototypes, some GTs with aero packages and historic cars with pronounced overhangs sometimes call for a bespoke approach. A slope extension, a tilting bed or a ramp system with a specific profile can prevent costly damage and stressful handling. The right equipment lets the driver and the team load the car with the same calm they bring to preparing for a session on track.
At Racing With Elegance, paddock equipment follows this approach: protecting the mechanicals, smoothing the team’s routine and presenting a setup worthy of your car. Once the car is on board, think about the tyres too: during transport and storage, Flatstoppers help prevent tyre flat spots. Before your next track day, take the time to test your climb cold, on level ground, with an observer: this quiet check often protects far more than a front lip.
Ramps for Low Cars: How to Load Your Car Safely
a ramp that is too short: with a track car, the problem often comes down to a few millimetres. Using ramps for low cars therefore means far more than simply placing them on the ground. You need a gradual, stable climb, perfectly aligned with the wheels, so that the aerodynamics, bodywork and mechanical components stay protected.
On a prepared GT, a race car, a lowered classic or a car fitted with a body kit, reduced ground clearance is part of the car’s identity. It should not become a constraint every time you load. Well-chosen and correctly installed loading ramps turn this operation into a precise, quick and reassuring step in the paddock.
Ramps for low cars: understanding the approach angle
The first criterion is not the final height of the ramp but its slope. A tall, short ramp creates an angle that is too steep: the front wheels climb while the front lip, front diffuser or floor stays too close to the ground. A long ramp, on the other hand, spreads the height difference and reduces the risk of contact.
Your car’s approach angle depends on several factors: front overhang, the actual height of the front lip, tyre diameter, suspension and any aerodynamic appendages. A slightly lowered road car will accept a slope that a track car with an aggressive front splitter will refuse. Never rely solely on a “ramp for low cars” label.
The transition at the top deserves the same attention. Even with a gentle slope, an abrupt break between the ramp and the trailer bed can make the underside of the body touch as the rear wheels begin to climb. Ramps with a progressive profile, or ramp extensions, limit this rocking effect. For the lowest cars, two stages of incline may be preferable to a single, very steep ramp.
Measure before choosing your loading ramps
Before any purchase or first use, measure the ground clearance at the lowest point at the front. Do it with the car in its usual transport configuration: tyre pressures, ride height, splitter fitted and, if necessary, a fuel level close to reality. A variation of a few millimetres can change how a slope is negotiated.
Also note the distance between the tip of the front lip and the centre of the front wheel. This figure gives a more accurate idea of the angle the car can accept. If you use a trailer or a truck, measure the height difference between the ground and the bed, as well as the space available to deploy the ramps without creating a sideways slope.
The usable width must suit your track width and tyres. A ramp that is too narrow makes guiding difficult, especially with wide semi-slick tires or in the wet. A ramp that is too light, or not rated for the axle load, is no saving: it can bend, slip or deform. Always check the load rating stated for the pair, not just for a single ramp.
Prepare stable ground and a clean trailer bed
A good installation starts at ground level. Place the ramps on a firm, level surface, free of gravel, mud, oil or wet grass. A ramp that sits unevenly can tip as the wheel passes over it, however well it is built.
The trailer bed must be checked too. Damp patches, fuel traces and smooth metal surfaces reduce grip. Clean the contact area, then check that every hook, lip or retaining system is engaged as the manufacturer intends. A ramp simply leaned against the bed can slide back as the car gathers momentum.
Where the setup allows, secure the ramps with their dedicated anchoring system. If there is none, do not improvise with a strap placed at random: the restraint must prevent backward movement without pulling the ramp sideways. The aim is to keep two strictly parallel tracks throughout the climb.
Alignment matters more than speed
Find the centre of each front wheel before you start. On a low car, a sudden steering correction during the climb can push a tyre off the usable profile of the ramp or make a sidewall touch its edge. A second person, standing in the driver’s line of sight and never in front of the car, provides real safety.
Drive up slowly, without sharp acceleration or sudden braking. Momentum does not fix a slope that is too steep: it only increases the risk of the ramps moving and of an impact at the top. If the front lip gets dangerously close, stop. Change the angle, add an extension or choose a longer solution rather than forcing the climb.
Once the wheels are on the bed, immobilise the car before doing anything else. Handbrake, gear engaged where suitable for the transmission, then wheel chocks: each step matters before fitting the tie-down straps. Ramps never replace a proper securing procedure.
Mistakes that damage a low car
The first mistake is using ramps designed for domestic use to load a competition car. Their slope, width, material or load rating may be unsuitable. A fine car should not be compromised on the very piece of equipment that governs every entry into the truck or onto the trailer.
The second is overlooking the difference between lifting a car and loading it. Lifting ramps provide a working height, but they are not necessarily designed to reach a trailer bed. Conversely, a loading ramp should not be used as a maintenance support without clear approval from its manufacturer. To work under the car, use suitable lifting equipment and axle stands on a stable surface.
Finally, avoid improvised stacks of planks, wedges or plates. They may seem practical in an emergency, but their stability is rarely guaranteed and their transition is often abrupt. For a car with low ground clearance, equipment designed for the job remains the most elegant and most rational solution.
Adapt the solution to your paddock
The right choice depends on your environment. For an open trailer used occasionally, long, light ramps that are easy to position may be enough, provided they suit the car’s weight and ground clearance. For a team that regularly loads several cars, the priority shifts to repeatability: generous width, quick fixing, secure storage and resistance to intensive use.
Very low cars, prototypes, some GTs with aero packages and historic cars with pronounced overhangs sometimes call for a bespoke approach. A slope extension, a tilting bed or a ramp system with a specific profile can prevent costly damage and stressful handling. The right equipment lets the driver and the team load the car with the same calm they bring to preparing for a session on track.
At Racing With Elegance, paddock equipment follows this approach: protecting the mechanicals, smoothing the team’s routine and presenting a setup worthy of your car. Once the car is on board, think about the tyres too: during transport and storage, Flatstoppers help prevent tyre flat spots. Before your next track day, take the time to test your climb cold, on level ground, with an observer: this quiet check often protects far more than a front lip.